OptimFROG

OptimFROG
"reduce at maximum the size of audio files"
Developer(s)	Florin Ghido
Release	OptimFROG 5.100 (2016-09-02)
Type	Lossless
Recommended encoder	[[{{{recommended_encoder}}}|{{{recommended_encoder}}}]]
Website	losslessaudio.org

OptimFROG is a lossless audio codec with optional hybrid lossless/lossy encoding. It comes with a freeware (closed-source) command-line encoder/decoder and plugins for several players and processing front-ends, and an SDK to use in other applications. It is available for Windows, Linux, FreeBSD and MacOSX, all in both 32-bit and 64-bit versions. Encoders/decoders for its hybrid "DualStream" format, and for floating-point audio, are included in the distributions in separate executables.

OptimFROG is a codec that gives priority to compression size, sacrificing speed. Its default preset performs not far from Monkey's Audio “Extra High”, possibly at Monkey's “Insane” speed, and the highest compression settings might take 10x heavier CPU load, but generally achieving smaller files than any other end-user codec Positioning itself at, arguably, one extreme of the size/CPU load trade-off, it has a fairly small userbase – and unlike most notable codecs, there is apparently no 3rd party decoder available and no sign of ffmpeg reverse-engineering the format (like was done with TAK).

Features

For an end-user considering OptimFROG as an audio format – likely due to its compression ratios, possibly also its hybrid mode – some of the following features are quite common among lossless codecs, while some are more scarce (in particular, the end of this list). To compare OFR with other lossless codecs, see the HA Wiki's Lossless Codec Comparison.

• Seekable and streaming playback.
• Error handling. Audio checksum optional (use the --md5 option upon encoding, --check to verify it), but OFR can also check corruption without decoding (--verify), hence quicker than any decoding format. Decoder can continue through errors.
• High-resolution audio support: apparently, any sampling rate that the WAVE format supports (4 GiHz), up to 32 bits per channel. Like WavPack but unlike most other formats, it also supports floating-point format (through a different executable included in the distribution).
• Piping support for encoding, and support for RAW PCM input.
• Tagging. (APEv2, or ID3 – see below.)
• RIFF chunks supported for recreating also non-audio chunks of the original .wav files; by default, OptimFROG will restore to a .wav file bit-identical to the original.
• Can read certain malformed .wav files; in particular, some hacks employed to fit more than the 4 GB size limitation into .wav files. (It is unclear what malformed .wav files will be recreated bit-identical.)
• Can create Windows self-extracting archives, a unique feature after WavPack discontinued it in version 5.
• Hybrid lossy/lossless encoding supported. Like WavPack, but unlike other end-user codecs, OptimFROG can decode both lossy and lossless streams together, to be maintained in the same library. A separate encoder is included in the distribution.

Limitations

• Currently there is no hardware supporting the format and software support is limited. The official encoder/decoder is closed-source (but a an official library can be used in third-party applications). Also the format has no official specification, and little is known about it.
• No multichannel support.
• CPU intensive (slow) encoding and decoding, especially in the higher modes. Given that portable low-power devices are out of consideration as they cannot play the files anyway, speed might not be that much of a limitation with the power of modern computers. Still, users who consider playing OptimFrog files from a battery-powered laptop or tablet, might want to test battery life impact, especially since it varies over the settings.
• Encoder has no provision of adding tags.

Because OptimFROG – like MP3 – can accommodate both APE tags and ID3, tagging ambiguity could be an issue: one application might not read another's tags. A user would likely want to stick to one tag format. Mp3tag, MusicBrainz Picard and foobar2000 will write APEv2 tags (at least by default). According to the website, EAC will write ID3v1.1 tags to .ofr files – and apparently there is no way for it to write APEv2 as the encoder has no switches for it (contrast to EAC with WavPack).

Software support

Some of the software cited at http://losslessaudio.org/Compatible.php has disappeared. One may still obtain the Kermit front-end from Archive.org. Most of the following should work:

• foobar2000 (through plugin available at the OptimFROG website or a version updated for fb2k v2x64 by HA user marc2k3)
• Winamp (through plugin available at the OptimFROG website)
• XMPlay for Windows, BASS_OFR addon available at player's website.
• XMMS (?)
• dBpoweramp music converter
• Mp3tag for tagging.
• MusicBrainz Picard for tagging (no audio fingerprinting).

Links

• Official OptimFROG website
• HA Wiki's Lossless Codec Comparison originally by Rjamorim