LossyWAV

lossyWAV

lossyWAV
lossy pre-processor
Developer(s)	Nick.C
Release	TBC
Type	Lossy
Recommended encoder	latest
Website	Hydrogenaudio

lossyWAV is a lossy pre-processor for audio. It reduces bit depth of the input signal, which, when used in conjunction with certain lossless codecs, reduces the bitrate significantly compared to unpreprocessed compression. lossyWAV's primary goal is to maintain transparency with a high degree of confidence when encoding any audio data.

History

lossyFLAC was an experiment started by 2Bdecided with the aim of transparently reducing audio bit depth (making some lower bits zero), thereby taking advantage of FLAC's detection of consistently zeroed lower sample bits within each single frame, increasing coding efficiency.[1]

Nick.C ported the original MATLAB implementation to Delphi, and lossyFLAC proved itself to work with other lossless codecs, so the application name was changed to lossyWAV. Since then, Nick.C has heavily developed and built upon lossyWAV, with tuning performed with the help of halb27.

Naming

lossyWAV processed files are usually named with a double filename extension, to make them instantly identifiable. e.g. ".lossy.flac" would indicate an audio file which was processed using lossyWAV, and subsequently encoded using FLAC.[2]

Combinations of lossyWAV with each specific encoder are referred to as lossyX, where X is an abbreviation of the lossless codec name. Combination names are listed in the "known supported codecs" section below.

Presets

• -1: Disc space-saving alternative to lossless archiving for large audio collections.
• -2: General usage; a compromise between -1 and -3.
• -3: High quality preset for usage on a compatible DAP.[3] A comparison of portable media players is here, which shows FLAC and WMA Lossless compatibility among listed players.

Presets are, of course, not limited to these example uses. Preset -3 has proven to be more than acceptable for people who have been closely involved with development. It is up to the user to decide which preset to use for their own purposes.

Supported input formats

• WAV: 16, 24-bit; ≥32KHz PCM.

Known supported codecs

Recommended settings

Codec	lossyWAV parameters	Encoder parameters	Combination name
FLAC	—	-b 512	lossyFLAC
LPAC	—	-b512	lossyLPAC
MPEG-4 ALS	—	-l -n512	lossyALS
TAK	—	-fsl512	lossyTAK
WavPack	—	--blocksize=512	lossyWV
WMA Lossless	-wmalsl (same as -cbs 2048)	—	lossyWMALSL

Known unsupported codecs

• ALAC
• LA
• Monkey's Audio
• OptimFROG
• TTA

lossyWAV application settings

lossyWAV beta v0.5.1 : WAV file bit depth reduction method by 2Bdecided.
Delphi implementation by Nick.C from a Matlab script, www.hydrogenaudio.org

Usage   : lossyWAV <input wav file> <options>

Example : lossyWAV musicfile.wav

Quality Options:

-1            extreme quality [4xFFT] (-cbs 512 -nts -2.0 -skew 36 -snr 21
              -spf 22224-22225-11235-11246-12358 -fft 11011)
-2            default quality [3xFFT] (-cbs 512 -nts +1.5 -skew 36 -snr 21
              -spf 22224-22235-22346-12347-12358 -fft 10101)
-3            compact quality [2xFFT] (-cbs 512 -nts +6.0 -skew 36 -snr 21
              -spf 22235-22236-22347-22358-2246C -fft 10001)

-o <folder>   destination folder for the output file
-nts <n>      set noise_threshold_shift to n dB (-18.0dB<=n<=+6.0dB)
              (-ve values reduce bits to remove, +ve values increase)
-force        forcibly over-write output file if it exists; default=off

Codec Options:

-wmalsl       optimise internal settings for WMA Lossless codec; default=off

Advanced / System Options:

-snr <n>      set minimum average signal to added noise ratio to n dB;
              (0.0dB<=n<=48.0dB) Increasing value reduces bits to remove.
-skew <n>     skew fft analysis results by n dB (0.0db<=n<=48.0db) in the
              frequency range 20Hz to 3.45kHz
-cbs <n>      set codec block size to n samples (512<=n<=4608, n mod 32=0)
-fft <5xbin>  select fft lengths to use in analysis, using binary switching,
              from 64, 128, 256, 512 & 1024 samples, e.g. 01001 = 128,1024
-overlap      enable conservative fft overlap method; default=off

-spf <5x5hex> manually input the 5 spreading functions as 5 x 5 characters;
              These correspond to FFTs of 64, 128, 256, 512 & 1024 samples;
              e.g. 22235-22236-22347-22358-2246C (Characters must be one of
              1 to 9 and A to F (zero excluded).
-allowable    select allowable number of clipping samples per codec block
              before iterative clipping reduction; (0<=n<=64, default=0).

-window       select windowing function n (0<=n<=6, default=0); 0=Hanning
              1=Bartlett-Hann; 2=Blackman; 3=Nuttall; 4=Blackman-Harris;
              5=Blackman-Nuttall; 6=Flat-Top.
-clipping     disable clipping prevention by iteration; default=off
-dither       dither output using triangular dither; default=off

-quiet        significantly reduce screen output
-nowarn       suppress lossyWAV warnings
-detail       enable detailled output mode

-below        set process priority to below normal.
-low          set process priority to low.

Special thanks:

David Robinson for the method itself and motivation to implement it in Delphi.
Dr. Jean Debord for the use of TPMAT036 uFFT & uTypes units for FFT analysis.
Halb27 @ www.hydrogenaudio.org for donation and maintenance of the wavIO unit.

Frequently asked questions

• Question: Is it VBR?
• Short answer: Yes.

• Question: Is it transparent?
• Short answer: Almost certainly.

• Question: Is it lossless?
• Short answer: No.

• Question: Why should I use this?
• Answer:

• high quality
• extremely low chance of audible artefacts
• reasonable bitrates
• usable with unmodified, established lossless formats.

External links

• Current development thread
• Original lossyFLAC thread (no longer used)