Editing Recommended LAME

Jump to: navigation, search

Warning: You are not logged in.

Your IP address will be recorded in this page's edit history.
The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision Your text
Line 1: Line 1:
#REDIRECT [[LAME]]
+
=Introduction=
 +
 
 +
This article is meant to explain to the users what are the recommended settings to be used with [[LAME]] for highest quality [[MP3]] encoding.
 +
 
 +
These settings require Lame 3.94 or later. Lame 3.97beta found on this website is the recommended version ([[Lame Compiles|Check here to download]])
 +
 
 +
Avoid using alpha (a) versions of LAME. More often than not those are exclusively for testing purposes, if you want to help developers with feedback.
 +
 
 +
Note: At a given bitrate range, the quality scale is following: VBR is higher quality than ABR which is higher quality than CBR (VBR > ABR > CBR in terms of quality). The exception to this is when you choose the highest possible CBR bitrate, which is 320 kbps (-b 320 = --alt-preset insane).
 +
 
 +
''''VBR:'''' ''variable bitrate mode, the goal is to keep a constant quality and saving bits where possible without lowering the quality.''
 +
 
 +
''''ABR:'''' ''average bitrate mode varies bits around a specified target bitrate''
 +
 
 +
''''CBR:'''' ''constant bitrate mode is not efficient regarding distributing bitrate to more complex music parts and saving bits where it would be possible without lowering the quality of those music parts. Only recommended for usage in streaming situations where the upper bitrate margin must be strictly enforced.''
 +
 
 +
 
 +
''Note: all modes and settings mentioned in this topic belong to the specifications of the MP3 standard, and the resulting MP3s should be played by every standard-conform MP3-Decoder. If this shouldn't be the case, blame the manufacturer or developer of your MP3-Decoder/device. ''
 +
 
 +
 
 +
 
 +
==VBR (Variable bitrate) settings==
 +
*[[VBR]] can be useful to get good quality from a specific quality level. Size is less predictable than with [[ABR]], but the quality is usually better.
 +
 
 +
-V(number) where number is 0-9, 0 being highest quality, 9 being the lowest.
 +
 
 +
{| align=center border="1" cellpadding="5" cellspacing="0"
 +
|+'''List of recommended settings'''
 +
| '''Switch''' || '''Preset''' || '''Target Kbps''' || '''Y Switch''' || '''-b''' || '''Lowpass''' || '''Resample'''
 +
|-
 +
| -V 0 || --preset extreme || ~240 || || 128 || 19383 Hz - 19916 Hz ||
 +
|-
 +
| -V 0 --vbr-new || --preset fast extreme ||  ~240 || || 128 || 19383 Hz - 19916 Hz ||
 +
|-
 +
| -V 1 || || ~210 || || 128 || 18671 Hz - 19205 Hz ||
 +
|-
 +
| -V 1 --vbr-new || || ~210 || || 128 || 18671 Hz - 19205 Hz ||
 +
|-
 +
| -V 2 || --preset standard || ~190 || || 128 || 18671 Hz - 19205 Hz ||
 +
|-
 +
| -V 2 --vbr-new || --preset fast standard || ~190 || || 128 || 18671 Hz - 19205 Hz ||
 +
|-
 +
| -V 3 || || ~175 || Y || || 17960 Hz - 18494 Hz ||
 +
|-
 +
| -V 3 --vbr-new || || ~175 || Y || || 17960 Hz - 18494 Hz ||
 +
|-
 +
| -V 4 || --preset medium || ~165 || Y || || 17960 Hz - 18494 Hz ||
 +
|-
 +
| -V 4 --vbr-new || --preset fast medium || ~165 || Y || || 17960 Hz - 18494 Hz ||
 +
|-
 +
| -V 5 || || ~130 || Y || || 16538 Hz - 17071 Hz ||
 +
|-
 +
| -V 5 --vbr-new || || ~130 || Y || || 16538 Hz - 17071 Hz ||
 +
|-
 +
| -V 6 || || ~115 || Y || || 15826 Hz - 16360 Hz ||
 +
|-
 +
| -V 6 --vbr-new || || ~115 || Y || || 15826 Hz - 16360 Hz ||
 +
|-
 +
| -V 7 || || ~100 || Y || || 14581 Hz - 14968 Hz || 32000 Hz
 +
|-
 +
| -V 7 --vbr-new || || ~100 || Y || || 14581 Hz - 14968 Hz || 32000 Hz
 +
|-
 +
| -V 8 || || ~85 || Y || || 12516 Hz - 12903 Hz ||  32000 Hz
 +
|-
 +
| -V 8 --vbr-new || || ~85 || Y || || 12516 Hz - 12903 Hz || 32000 Hz
 +
|-
 +
| -V 9 || || ~65 || Y || || 9774 Hz - 10065 Hz || 24000 Hz
 +
|-
 +
| -V 9 --vbr-new || || ~65 || Y || || 9774 Hz - 10065 Hz || 24000 Hz
 +
|}
 +
 
 +
==ABR (average bitrate) settings==
 +
''(128 kbit/s ABR: roughly the same filesize as 128 kbit/s CBR)''
 +
 
 +
* '''[[ABR]] Setting tuned from 320 kbit/s down to 80 kbit/s'''
 +
** --preset <bitrate>
 +
::  Example: --preset 200
 +
 
 +
* '''128 kbit/s ABR'''
 +
** -V5 --athaa-sensitivity 1 (when using >= LAME 3.96.1, for best results at 128kbps)
 +
** --preset 128
 +
 
 +
 
 +
==CBR (constant bitrate) settings==
 +
 
 +
*'''[[CBR]] Setting tuned from 320 kbit/s down to 80 kbit/s'''
 +
** -b <bitrate>
 +
::  Example: -b 96
 +
 
 +
* '''128 kbit/s CBR'''
 +
** -b 128
 +
 
 +
:  note: --b 320 is the exact same thing as --preset insane
 +
 
 +
:  Valid values for CBR encoding are 8, 16, 24, 32, 40, 48, 64, 80, 96, 112, 128, 160, 192, 256 or 320
 +
 
 +
 
 +
=Additional reading=
 +
 
 +
* [[LAME]]
 +
* [[EAC_and_Lame | Configuring EAC and LAME with recommended settings]]

Please note that all contributions to Hydrogenaudio Knowledgebase are considered to be released under the GNU Free Documentation License 1.2 (see Hydrogenaudio Knowledgebase:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

Cancel | Editing help (opens in new window)